|
|
Electrical Equipment & Accessories
|
Suppliers Directory
|
VISHAL ELECTROMAG INDUSTRIES
Stepper Motors Geared/ungeared , Synchronous Motor Geared/ungeared , Pmdc Geared Motor Mini, Gears Plastic Moulded.
| | Products : |
Stepper Motors Geared/ungeared , Synchronous Motor Geared/ungeared , Pmdc Geared Motor Mini, Gears Plastic Moulded. |
| Address : |
D-202, BONANZA INDUSTRIAL ESTATE, 2ND FLOOR, ASHOK NAGAR, KANDIVLI (EAST), |
| Telephone : |
(91)-(22)-28872821/288703930 |
| Fax : |
(91)-(22)-28870393 |
| Send : |
On-Line Trade Inquiry |
| |
|
Products |
|
PLASTIC MOULDED GEARS - VISHAL ELECTROMAG HAS CONSTRUCTED A 20 DP MOULDED DELRIN GEAR RANGE. STANDARD SIMPLE GEARS HAVE ALUMINIUM AT THE CENTRE WITH HOLE DIA 3/8" OR 5/8" AND WITH 3 SCREWS FOR EASY MOUNTING. STANDARD TEETH AVAILABLE ARE 24, 30, 36, 40, 48, 64, 80, 96, AND 108. GEARS WITH 12, 16, 20 AND 24 TEETH ARE AVAILABLE WITHOUT CENTRE ALUMINIUM BUSH AND WITH 3/8" HOLE DIA OR WITH SLOT. COMPOUND GEAR (IE, GEAR/PINION ASSEMBLY) SINGLE PIECE MOULDED IS A AVAILABLE WITH GEAR RATIO OF 1:2-20 X 40 TEETH, 1:3-16 X 48 TEETH AND 1:4-12 X 48 TEETH.
|
|
PLASTIC MOULDED GEAR - VISHAL PRESENTS 20 DP MOULDED DELRIN GEAR RANGE. DELRIN IS STRONGEST MATERIAL AND NEEDS NO LUBRICATION FOR GEARS. NORMALLY THE STANDARD SIMPLE GEARS ARE HAVING ALUMINIUM AT THE CENTRE WITH HOLE DIA 3/8" OR 5/8" AND WITH 3 SCREWS FOR EASY MOUNTING. STANDARD TEETH OFFERED ARE 24, 30, 36, 40, 48, 64, 80, 96, AND 108. GEARS WITH 12, 16, 20 AND 24 TEETH ARE OFFERED WITHOUT CENTRE ALUMINIUM BUSH AND WITH 3/8" HOLE DIA OR WITH SLOT. COMPOUND GEAR (IE, GEAR/PINION ASSEMBLY) SINGLE PIECE MOULDED IS AVAILABLE WITH GEAR RATIO OF 1:2 -20 X 40 TEETH, 1:3 - 16 X 48 TEETH AND 1:4-12 X 48 TEETH. THESE SIMPLE AND COMPOUND GEARS CAN BE USED IN SPECIAL PURPOSE MACHINES OR TRANSMISSION DRIVES. THEY CAN ALSO BE USED WITH AC SYNCHRONOUS MOTORS OR DC STEPPING MOTORS.
|
|
DC STEPPER MOTORS - INTRODUCED BY VISHALK ELECTROMAG INDUSTRIES THE DC STEPPER MOTORS ARE HYBRID TYPE TWO-PHASE OR FOUR PHASE UNI POLAR OR BIPOLAR MOTORS, WHICH TRANSFER ELECTRONIC SIGNALS INTO MECHANICAL MOTION. THE MOTOR SHAFT CIRCLES AT 200 STEPS/REV IN FULL STEP MODE OR 400 STEPS/REV IN HALF STEP MODE AND CAN BE DRIVEN IN EITHER DIRECTION. IT CAN BE DRIVEN AT HIGH STEPPING RATES WITH CHOPPER CURRENT DRIVE. THESE STEPPING MOTORS SUBMITS MANY ADVANTAGES AS AN ACTUATOR IN A DIGITALLY CONTROLLED POSITIONING SYSTEM. THEY CAN EASILY BE INTERFACED WITH A MICROCOMPUTER OR MICROPROCESSOR TO CATER OPENING, ROTATING, REVERSING, CYCLING, CLOSING AND HIGHLY ACCURATE POSITIONING IN A WIDE VARIETY OF APPLICATIONS. MECHANICAL COMPONENTS SUCH AS CLUTCHES, GEARS, BRAKE AND BELTS ARE NOT REQUIRED SINCE STEPPING IS ACCOMPLISHED ELECTRICALLY. BECAUSE OF DETENT TORQUE, THE MOTOR APPLIES HOLDING TORQUE AT STANDSTILL TO HELP BLOCK UNWANTED MOTION. THE MOTORS RUGGED CONSTRUCTION ENDS IN LONG LIFE AND ELIMINATES THE NEED FOR REGULAR MAINTENANCE. THESE STEPPER MOTORS ARE OFFERED IN A NEMA FRAME SIZES 2.3" (DIA 58 MM), 3.4" (86 MM), AND 4.2" (108 MM), WITH FULL STEP ANGLE 1.8° AND HALF STEP ANGLE 0.9° AND STEP ACCURACY OF ±5% NON- CUMULATIVE. VOLTAGES AVAILABLE ARE 5, 6, 12 OR 24 V DC. HOLDING TORQUE IS AVAILABLE FROM 2 KG.CM (IN 12 DIFFERENT MODELS.) IMPORTED STEPPER MOTOR REWINDING/REPAIRING CAN ALSO BE DONE, OR ITS EQUIVALENT MOTOR CAN BE AVAILED.
|
|
STEPPER MOTOR DRIVE - PRESENTING A STATE-OF-THE-ART TECHNOLOGY STEPPER MOTOR DRIVE, WITH INTERFACING OF MICROPROCESSOR OR MASTER CONTROLLERS (MAY BE A PC OR PLC) IN MULTI-AXIS POSITIONING SYSTEMS, FOR STEPPER MOTORS. THE DRIVE IS DESIGNED ON THE PRINCIPLE OF CURRENT PULSE WIDTH MODULATION FOR SWITCHING OF CURRENTS THROUGH THE WINDINGS OF THE STEPPER MOTOR. FEATURES: LOW COST AND MOST COMPACT DESIGN; CAN DRIVE UNIPOLAR/BIPOLAR STEPPER MOTOR; MAINS 230 V AC 50 HZ OPERATED WITH IN-BUILT DC POWER SUPPLY AND STEPPER MOTOR DRIVE LOGIC GENERATION; FREQUENCY RANGE APPROX 40 TO 900 PPS (OTHER FREQUENCY AVAILABLE ON REQUEST).
|
|
SYNCHRONOUS MOTORS - GEARED/UNGEARED
|
|
PLASTIC MOULDED GEARS - 20DP, SIMPLE & COMPOUND SPUR GEARS,12 TEETH TO 180 TEETH.
|
|
PMDC GEARED MOTORS - 12V DC, 10,40,55 RPM MINIATURE 3W & 12W
|
|
PLASTIC MOULDED GEARS - VISHAL ELECTROMAG HAS CONSTRUCTED A 20 DP MOULDED DELRIN GEAR RANGE. STANDARD SIMPLE GEARS HAVE ALUMINIUM AT THE CENTRE WITH HOLE DIA 3/8" OR 5/8" AND WITH 3 SCREWS FOR EASY MOUNTING. STANDARD TEETH AVAILABLE ARE 24, 30, 36, 40, 48, 64, 80, 96, AND 108. GEARS WITH 12, 16, 20 AND 24 TEETH ARE AVAILABLE WITHOUT CENTRE ALUMINIUM BUSH AND WITH 3/8" HOLE DIA OR WITH SLOT. COMPOUND GEAR (IE, GEAR/PINION ASSEMBLY) SINGLE PIECE MOULDED IS A AVAILABLE WITH GEAR RATIO OF 1:2-20 X 40 TEETH, 1:3-16 X 48 TEETH AND 1:4-12 X 48 TEETH.
|
| |
|
View More Supplier Pages
Page(s) : 1 •
2 •
3 •
4 •
5 •
| |
|
|
|
